dr pen a6s how to use

1. Pre - use Preparation
   • Device Charging: Ensure the device is fully charged before use. When charging, connect the instrument to the power supply. The charging indicator light is red during charging and turns green when fully charged. It supports a dual - power supply mode, which can be used with a plug - in adapter and a 6 - foot - long power cord for AC power, or with two lithium - ion batteries for wireless use.
   • Cartridge Selection: Select an appropriate cartridge according to your skin condition and treatment needs. The Dr Pen A6S is equipped with various cartridges, such as 11 - needle, 16 - needle, 24 - needle, 36 - needle, 42 - needle, as well as different types like nano needles, s nano, 5d nano, 3d nano. For example, shorter needles are suitable for sensitive areas like the cheeks, while longer needles are more suitable for thicker - skinned areas like the forehead.
   • Cleaning and Disinfection: Thoroughly clean your facial skin to remove dirt, oil, and makeup residues, ensuring that the microneedles can act effectively on the skin. Also, clean and disinfect your hands to avoid contamination. If using alcohol for disinfection, wait for the alcohol to completely evaporate before proceeding with the next steps.
   • Skin Anesthesia (Optional): To reduce discomfort during the treatment, apply an appropriate amount of numbing cream evenly on the cleaned skin and cover it with plastic wrap. Wait for 15 - 30 minutes until the skin feels numb, then gently wipe off the numbing cream and clean the skin again. However, not everyone needs to use numbing cream, and it can be decided according to your individual pain tolerance.

1. Device Setup
   • Cartridge Installation: Insert the selected cartridge into the device, turn it clockwise and push it out horizontally to ensure it is firmly installed. Be careful not to touch the needles during the installation process to prevent stabbing and contamination.
   • Needle Length Adjustment: Rotate the scale adjustment ring on the device to adjust the needle length. Turning it clockwise shortens the needle depth, while turning it counter - clockwise increases the needle depth. Select the appropriate depth according to different treatment areas and skin conditions. For example, when treating eye fine lines, a shorter needle depth can be chosen; when treating acne scars, the needle depth can be appropriately increased.
   • Speed Adjustment: Press and hold the power button for 2 - 3 seconds to turn on the device. The device features a built - in LED display and six - level speed adjustment. For first - time users or those with sensitive skin, it is recommended to start from a lower speed, such as level 1 or 2. After getting used to it, the speed can be gradually increased according to personal feelings and treatment needs, with a maximum of level 6.
2. Treatment Process
   • Operation Technique: Hold the device perpendicular to the skin and gently slide it over the treatment area in vertical, horizontal, and diagonal directions to ensure uniform coverage. Apply moderate pressure during the operation to avoid excessive pressing on the skin, which may cause unnecessary pain and damage.
   • Treatment Sequence: Treat the areas in the order of cheeks, forehead, chin, and both sides of the nose. For different areas, the needle length and speed can be adjusted flexibly according to the skin thickness and sensitivity. For example, the cheek area has relatively thin and sensitive skin, so a lower speed and shorter needle length can be used; the forehead has thicker skin, and the needle length and speed can be appropriately increased.
   • Treatment Time: The treatment time for each area can be determined according to the skin condition and the severity of the problem, usually 1 - 3 minutes for each area. The entire facial treatment time should be controlled within about 15 - 30 minutes to avoid over - treatment and burdening the skin.
3. Post - use Care
   • Skin Care: After the treatment, the skin is in a relatively sensitive state and needs to be cared for promptly. Gently wipe the exudate on the skin surface with normal saline, and then apply a serum or facial cream with repair and moisturizing effects to help the skin recover and lock in moisture. Within 24 hours after the treatment, avoid using irritating skin care products, cosmetics, and getting the skin wet to prevent infection.
   • Cartridge Cleaning: Thoroughly clean the cartridge with alcohol. You can soak the cartridge in an alcohol solution with a concentration of 70% or higher for a few minutes or spray the needle part with an alcohol spray. After cleaning, let the cartridge air - dry naturally and store it properly for future use (if it is a disposable cartridge, discard it as required).
   • Device Storage: Turn off the device and store it properly to avoid collision and damage. If using battery - powered operation, it is recommended to remove the batteries when the device is not used for a long time to prevent battery leakage from corroding the device.
4. Usage Frequency and Precautions
   • Usage Frequency: It is recommended to determine the usage frequency according to your individual skin recovery situation, generally 1 - 2 times a week. Excessive use may cause skin damage, infection, and other problems, affecting skin health.
   • Contraindicated Groups: People with skin diseases (such as severe acne, eczema, psoriasis, etc.), open wounds on the skin, pregnant women, lactating women, and those allergic to microneedle treatments are not suitable for using the Dr Pen A6S microneedling pen.

Related Products

Add To Cart

Dr. Pen A6S Smart Microneedling Pen -Giveaway 10 Replacement Cartridges

$115.99 $159.99

Sale 27%

Add To Cart

Dr. Pen A6S Cartridges 10 Pack (7 Options)

$20.99